DC 12V Temperature Controller Denoised Speed Controller ON/OFF for PC Fan/Alarm

Description

Store Categories
Store Categories
eBay Motor
Fashion
Books, Movies & Music
Electronics
Collectibles & Art
Home & Garden
Sporting Goods
Toys & Hobbies
Business & Industrial
Health & Beauty
Other
Product View
Detail
1. Description:
The controller is suitable for automatic control of DC fan speed with temperature when the 12V current is not greater than 0.8A.
2. Parameters:
Parameter
Value
Operating voltage
DC12V can work in 9-14V range
Fan interface
2510-3P bend (pin spacing 2.54mm)
Fan current
Less than 0.8A
Protection
Input reverse connection protection.
No output overload protection!!! Please note that the output should not be short circuited or overloaded
Drive output range
5% -100 part fan low output may not turn,
please adjust the fan can start the use of position
Operating temperature
-20 Celsius to 60 Celsius
Temperature probe parameters
NTC 50K B=3950
Probe temperature
Small black head 120 degrees
Ring probe 110 Celsius
Board size
43mm*18mm*9mm (excluding extended interface)
Fan interface extends 8mm
Setting parameters default factory
Low speed 20%.
Acceleration temperature 30.
Acceleration width 5.
Do not shut down the output.
At this temperature setting, holding the probe with the palm of the hand will accelerate in a few minutes. If the probe is clamped into the armpit, it will reach full speed in 2 minutes.
3. Components:
1>. Input line: red black power line is only welding 12V positive and negative power cord, as a
general use. The three wire connector is equipped with a 2510-3P plug, which is used to
measure the speed of some main board three wire fan ports. Large 4P interface facilitates
power acquisition from chassis.
2>. temperature probe: small black line’s head is short, low heat capacity. It is suitable for
testing narrow space and air temperature, and the response is relatively fast. The ring probe
is enclosed inside a ring metal head with a diameter of 4.2mm. It is suitable for mounting on
the radiator or other heating object surface with screws.
4. Features:
1>. 12V 2--3 line fan temperature speed controller
2>. Manual automatic integration control output without pulse
3>. Noiseless and non burning fan
4>. MCU control is precise and gentle
5>. Set auto save and shut down Fan
5. Manual automatic integration control:
1>. Manual control without temperature probe. Click / double-click (double-click speed not too
fast) button up / down gear. Each shift continues after 20 seconds, and the gear is
automatically stored. The No. 2 indicator flashes rapidly in 20 seconds (when the temperature
control is invalid). When the flash is stopped, it indicates that the file has been stored. The 3 /
1 indicator light is always on when you can not continue to increase / not continue to reduce
the position.
2>. When the temperature probe is installed, the manual speed is used as the initial low
speed (bottom line speed). When the temperature exceeds the accelerating temperature, the
fan speed accelerates smoothly with the increase of temperature.
When the temperature reaches and exceeds the sum of the acceleration temperature and the
acceleration width (full speed temperature), the fan runs at full speed.
Set the acceleration temperature and acceleration width parameters as shown in the
schematic diagram below. The number 123 represents the indicator light on the board (red)
and the (white) state is displayed in binary order:
3>.Fan shutdown strategy setting:
First, power off and remove the fan. Press the set button to electrify the controller. Keep the
settings button always hold (about 3 seconds) until the three lights turn into double flash state
and then release the button.
The indicator lamp turns into a single light, which represents the entry mode setting state.
The controller is divided into three kinds of working modes, corresponding to 1, 2, 3 indicator
light double flashing, through short press button switch, set the long, press the button to save
and exit the set mode and automatically back to normal working state. The three working
modes are as follows:
1. Do not shut down the output.
2. Shut down output below 2 Celsius acceleration.
3. Shut down output below 5 Celsius acceleration.
6. Example instruction:
Set the acceleration temperature of 35 degrees Celsius, accelerate the width of 10 degrees
Celsius, shut down strategy mode 3 (lower than the accelerating temperature of 5 degrees
Celsius shut down). After this setting, when the power supply is lower than 35 degrees, the
fan does not turn. When the temperature rises to 35 degrees centigrade, the fan starts
according to manual setting. The temperature continues to rise, the speed of the flat
acceleration, reaching and above 45 degrees Celsius, the fan full speed. When the
temperature drops to 35-30 degrees Celsius, the fan always operates according to manual
setting speed, below 30 degrees fan stops.
Note that the fan shut down strategy is controlled by the hysteresis mode, which can
effectively prevent the fan repeatedly switching near the critical point. For example, after the
above settings, the temperature rise to 35 degrees Celsius, start the fan, cool down below 30
degrees Celsius, turn off the fan.
7. Warm tips:
Because most fans operate at low output, they cannot be started. So when setting the
minimum speed of temperature control, should be adjusted to the minimum, and let the fan
stop by hand. And then, step by step, high output until the fan starts up. After the actual
settings, do not lower than this position, otherwise the fan may not start at low speed.
Buyer show:
Feedback
Payment
Shipment
About us
Feedback
We appreciate positive feedback . we always try our best to service our customers .
so if you
have ant question ,PLEASE DON’T HESITATE TO TELL US,
we are always here to offer help .
Payment
We prefer PayPal .For purchasing multiple items , please contact us for a combined invoice .
generally we would like to receive payment thin 48 hours if .
Shipment
We provide airmail service with good package . The items will be shipped within the nest
2 business days after we received the payment . when you buy multiple items ,your shipping
cost will be combined with discount .
SHIPPING
TIME
(weekends/holidays
excluded)
Country
Name
Shipping
Time
Country
Name
Shipping
Time
USA/Canada
10
-15d
Spanish/Portugue
10-25d
East/South
Asia
10
-15d
France/West Asia
10-25d
United
Kingdom
10 -20d
Italy
10-30d
Australia/New Zealand
10 -15d
West
Asia/Middle
East
15-25d
Most
Country
of
West/North Europe
10-20d
South
America
and
Africa
15-30d
East /Middle
Europe/Russia
10-25d
About us
NEW, GOOD QUALITY, ORIGINAL PACKAGE
LARGE STORE AND THE LOWEST PRICE
NO-QUESTION-REFUND,
FOR LARGE QUANTITY ,OFFER BETTER PRICE,
ORIGINAL
PACKING(TAPE REEL/TUBE/TRAY）
We specialize in electronic components . ICs, Capacitors, Diodes, Resistors,
LEDs,
Transistors, and so on.
Especially in Hard To Find Parts .
we only sell
NEW ,
ORIGINAL parts . please buy with confidence .We offer
NO-QUESTION-REFUND
go to my store